![]() If so and you are using a premade 100 foot power cord I have seen them fail to boot due to voltage drop on those premade cablesĪlso if the power supply you are using has not got high enough wattage rating it will drop to below 11.8 volts with load and the camera will not power up either. paper clip salute!Īs a off note how ever most of the “Non Dahua branded” and other knock off lower end cameras default to 192.168.0.*** that I have seen usually it is 100 or 10 If it does not work that way you have a issue with camera.Īnd if a hard reset does not clear it then time for RMA. Restart the power to camera and watch for any response. cgi-bin/configManager.cgi?action=setConfig&Lighting.MiddleLight.1 cable from port on hub to pc hard wired and static ip to 192.168.1.110 use a gateway of 192.168.1.1 does not matter but that will avoid nag from winders or nux depending on your pc OS flavor cgi-bin/configManager.cgi?action=getConfig&name=Lighting. It's not in the API (v1.67), and I personally had no luck looking for it. I’d love to hear how you discovered this ‘Lighting’ command. cgi-bin/configManager.cgi?action=setConfig&= 50 -> Intensity cgi-bin/configManager.cgi?action=setConfig&Lighting.Mode= Off -> Off cgi-bin/configManager.cgi?action=setConfig&Lighting.Mode= Manual -> Manual cgi-bin/configManager.cgi?action=getConfig&name=Lighting It's not in the API (v1.67), and I personally had no luck looking for it.Īfter experimenting today, here’s what I’ve learned for my Dahua varifocal cams (HDW2231R-ZS, HDW5231R-ZE). cgi-bin/configManager.cgi?action=setConfig&VideoInDayNight.Mode=ColorĬlick to expand.Thanks BHj!. May sometimes make sense to force to color via cgi-bin/configManager.cgi?action=setConfig&VideoInDayNight.Mode=Brightness cgi-bin/configManager.cgi?action=setConfig&Lighting.Mode=ZoomPrio cgi-bin/configManager.cgi?action=setConfig&Lighting.Mode=Auto It seems that it might not be a good idea to use more than 100 in total. The SD49555 tas 6 IR leds, where nearlight (2leds) and farlight (4 leds) can be controlled separately. cgi-bin/configManager.cgi?action=setConfig&Lighting.Mode=Manual&=50&=50 then the leds can be manually controlled with cgi-bin/configManager.cgi?action=setConfig&VideoInDayNight.Mode=BlackWhite cgi-bin/configManager.cgi?action=setConfig&Lighting.Mode=Offįor the IR leds to be on, the camera has to be in B/W mode. These are not documented in any doc I have seen, so thought I'd post here ![]() I am not sure if this will help you, but I experimented a bit and found the following things to work for my purpose. I wanted to get better control over the IR leds, and did not really like having to mess around with the day and night mode. When things were totally messed-up, starting at 'zero-zero' then executing method 'B' so far has worked every time. These frequently left one or more of my cameras 'locked in' with a blurry image. It proved handy in development when I was experimenting with shorter sleep durations (<3 seconds). I added a commandline argument to optionally send the following 'zero-zero' command BEFORE executing method B. (I used the same Day Zoom, Day Focus, Night Zoom, Night Focus values that I configured into the DahauSunriseSunset tool.)Ģ. ![]() In a loop, I execute 1 adjustFocus command for each camera, then the sleep command, then repeat 4 more times. To reduce the script run time, I settled on using master sleep duration. In case this helps anyone else, here's a few details about my approach.ġ. Anything less resulted in at least one of four out-of-focus cameras. I had to experiment with the sleep duration and settled on 4 seconds. I've completed my testing and have settled on course 'B'.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |